Eppendorf Galaxy Gas Analyzer User Manual

Instructions — Galaxy® CO₂ Sensor SetupGalaxy® CO2 Sensor Setupseeon p.Fig.Tab.p.Instructions New Brunswick CO2 IncubatorsGalaxy® CO2 Sensor SetupIn

Galaxy® CO2 Sensor Setup — Instructions1010. Replacement Expansion PCB fitting:170 R - Refitting is a reversal of removal. Follow the wiring diagram

11Galaxy® CO2 Sensor Setup — Instructions11. 170 R CO2 Sensor fittingUnpack the new CO2 Sensor and fix in place with the bracket supplied and the or

Galaxy® CO2 Sensor Setup — Instructions1213. Route the tube from the Auto-Zero Pump “Out” (see Pump diagram at the bottom of Page 7) to the bottom b

13Galaxy® CO2 Sensor Setup — Instructions16. 48 R CO2 Sensor fitting:NOTE for 48 R: The replacement CO2 Sensor has tubing pre fitted for the 170 R.

Galaxy® CO2 Sensor Setup — Instructions1417. Disconnect the tube from the Auto-Zero Pump “Out” (see Pump diagram at bottom of page 7) and connect t

15Galaxy® CO2 Sensor Setup — Instructions19. Refit the insulation block and trim a small pocket in the insulation to locate the connecting block (as

Galaxy® CO2 Sensor Setup — Instructions1622. EPROM ReplacementNOTE: To avoid static damage, take anti-static precautions and avoid touching the legs

17Galaxy® CO2 Sensor Setup — Instructions2 Galaxy 17 0 S 230 V / 120 V CO2 Incubators2 Galaxy 170 S 230 V / 120 V CO2 Incubators2.1 K2 CO2 Sensor up

Galaxy® CO2 Sensor Setup — Instructions182.2 Removing existing parts1. Power down the Incubator and completely disconnect from the Mains/Power Suppl

19Galaxy® CO2 Sensor Setup — Instructions4. Remove the existing CO2 Sensor by disconnecting the 5 way Molex connector and then unplug the Auto-Zero

April 25, 2012Revision ACO2SENS-0060CopyrightCopyright© 2012 New Brunswick Scientific Co., Inc., USA. No part of this publication may be reproduced

Galaxy® CO2 Sensor Setup — Instructions206. Locate the Auto-Zero Pump and disconnect the tubing leading to the CO2 Sensor from the Auto-Zero Pump (s

21Galaxy® CO2 Sensor Setup — InstructionsWAGO connecting block with Auto-Zero Pump connections highlightedFitting the new Parts8. Fit the new Pump w

Galaxy® CO2 Sensor Setup — Instructions22Door Harness ConnectorsSolenoid Pump Valve PCB bracket mounting points11. Mount the PCB/bracket in the tray

23Galaxy® CO2 Sensor Setup — Instructions12. Route the Red/Black wires from the PCB to the Auto-Zero Pump connections on the WAGO connecting block.

Galaxy® CO2 Sensor Setup — Instructions2414. Connect the Solenoid Valve Neutral (Black wire with Crimp Female Spade) to a spare location on the Neut

25Galaxy® CO2 Sensor Setup — Instructions17. Cable zip tie all wires in place to secure to tray.18. Unpack the new CO2 Sensor and fix in place with

Galaxy® CO2 Sensor Setup — Instructions2619. Route the Auto-Zero inlet tubing from the CO2 Sensor (pre fitted to the new Sensor) down between the in

27Galaxy® CO2 Sensor Setup — Instructions21. Cut the old Pump tubing in line with the glass fibre insulation and also trim the CO2 Sensor wiring har

Galaxy® CO2 Sensor Setup — Instructions2823. Refit the insulation block and trim a small pocket in the insulation to locate the connecting block (as

29Galaxy® CO2 Sensor Setup — Instructions3 Galaxy 48 S / 14 S 120 V & 230 V CO2 Incubators3 Galaxy 48 S / 14 S 120 V & 230 V CO2 Incubator

3Galaxy® CO2 Sensor Setup — Instructions1 Galaxy 170 R / 48 R 120 V / 230 V CO2 Incubators1 Galaxy 170 R / 48 R 120 V / 230 V CO2 Incubators1.1 K1 C

Galaxy® CO2 Sensor Setup — Instructions302. Rear cover removal: 48 S – Remove the CO2 Sensor access panel by unscrewing the 4 x Pozidriv head screws

31Galaxy® CO2 Sensor Setup — InstructionsFitting the new CO2 Sensor5. 48 S CO2 Sensor fittingUnpack the new CO2 Sensor and fix in place with the bra

Galaxy® CO2 Sensor Setup — Instructions32NOTE: Large slotted screw replaced with brass straight barbed connector and sealing black cap.Photograph &q

33Galaxy® CO2 Sensor Setup — InstructionsGalaxy 14 with O2 optionNOTE: O2 inlet connector assembly is adjacent to sensor bracket, but does not cause

Galaxy® CO2 Sensor Setup — Instructions347. Refit the insulation block and trim a small pocket in the insulation to locate the connecting block (as

35Galaxy® CO2 Sensor Setup — Instructions3.3 To complete the installation the new CO2 Factors must be entered as follows1. Power up the Incubator an

Galaxy® CO2 Sensor Setup — Instructions36

Your local distributor for New Brunswick products: www.nbsc.com/ContactUsEppendorf AG · 22331 Hamburg · Germany · Tel: +49 40 538 01-0 · Fax: +49 40 5

Galaxy® CO2 Sensor Setup — Instructions41.2 Removing existing parts1. Power down the Incubator and completely disconnect from the Mains/Power Supply

5Galaxy® CO2 Sensor Setup — Instructions3. With the access panel removed, locate the insulation block covering the CO2 Sensor and carefully remove t

Galaxy® CO2 Sensor Setup — Instructions648 R – Remove the Top Cover by unscrewing the 4 x large Pozidriv head screws. Pull the Top Cover forward and

7Galaxy® CO2 Sensor Setup — InstructionsCarefully snip zip ties.Secure top cover as shown.Re-secure top cover when complete.NOTE: Now procede to ste

Galaxy® CO2 Sensor Setup — Instructions87. Existing Expansion PCB removal:170 R – Using the diagram below with points highlighted in yellow:1. Disco

9Galaxy® CO2 Sensor Setup — InstructionsFitting the new Parts8. Solenoid Valve fitting:170 R - Mount the Solenoid Valve to the new cover plate using